Power supply input: 24 Vdc ±5%;1500 Vac isolation between networks;Very low DC leakage current at repeater inputs;Each repeater can extend the Fieldbus network length up to 1900 meters;Provides up to 125 mA at 18 V to the fieldbus network for field devices;Includes terminators on output (H1 network);
Smart Temperature Transmitter for use in Safety Instrumented Systems;± 0.02% accuracy;Built-in thermocouples and RTD’s linearization;Small and lightweight;Intrinsically safe;Signal simulation for loop test.
PROFIBUS HUB REPEATER;IP 20 classification;• 5 insulated channels;• Transparent for all PROFIBUS DP protocol versions;• RS-485 specifications for each channel;• Maximum 12 Mbps communication rate;• Supports up to 31 devices per channel.
Based on Time Domain Reflectometry (TDR) principle• Not affected by density and/or temperature variations• Not affected by viscosity, gravity, steam or gases over the process• Easy to install and maintain• ±7 mm accuracy• Excellent repeatability and resolution
Available in 3 technologies: HART®(LD301), Foundation™ Fieldbus (LD302) and PROFIBUS PA (LD303).Configured with SMAR software and other manufacturer configuration tools.
Accuracy ± 0.2%;Several rod lengths up to 3200mm;Insertion rod materials: AISI304L or AISI316L;Diaphragm materials: AISI316L or Hastelloy C276.WirelessHART Protocol, HART Version 7
Intelligent Pressure Transmitter With Control Capability;Update output current in 100 ms with 0.75 µA/bit resolution;Improved performance due to dedicated math co-processor;Multi-drop operation mode;PID control function;Supports DTM and EDDL;
0 ~ 125 Pa to 0 ~ 25 MPa• 0 ~ 0.5 inH20 to 0 ~ 3600 psi• ± 0.075% Accuracy• 40:1 Rangeability• Wetted parts in 316 SS, Hastelloy• Totally digital; including sensor, electronics and communication;• Digital LCD display
± 0.045% Accuracy• ± 0.2% of URL Stability - Guarantee For 12 Years• 200:1 Rangeability• 35 ms Total Response Time• Non-volatile Flow Totalizer• Tank Linearization
OPT-700 –Serial to Fiber Optic Converter;Works directly in LC700/DFI backplane;Used in a stand-alone mode with an external power supply;Accepts EIA-232-C or EIA-485 with configurable baud rates;Supports Point-to-Point or Multidrop Fiber Optic communication.
Active impedance control device ;Output 320 mA (max);Power Supply 24 to 32 Vdc ± 10 %;Ambient Temperature Limits -20 to 50 ºC (-4 to 122 ºF);Ambient Humidity Limits 10-95% RH.
Accuracy ± 0.045%;Stability of ± 0.2% of the URL – 12-year guarantee;Rangeability of 200:1;Advanced diagnostics;Supports DD, EDDL and FDT/DTM;Simple and complete local adjustment: (zero and span calibration);
PS302P - POWER SUPPLY FOR FIELDBUS;Non-intrinsically safe equipment with a universal AC input;Short circuit and overcurrent protection, ripple and fault indication.
1500 VAC Isolation between networks· Very Low DC leakage at repeater inputs· Each unit can extend the Fieldbus network length up to 1900 meters;· Includes selectable bus terminators on both network sides;· Accommodate conductors up to 2.5mm2 (12 AWG).
PROFIBUS-DP/MODBUS RTU REPEATERIP 20 classification;• 1 insulated channel;• Transparent for all PROFIBUS-DP protocol versions;• RS-485 specifications;• Maximum 12 Mbps communication rate;• Supports up to 31 devices;• Supports up to 1200 m length of spur line;
WirelessHART™ digital communication, HART Protocol Version 7;Increment the communication routes facilitating the WirelessHART™ network scalability;Increase reliability through alternate paths on the Mesh network;Solution with excellent cost/benefit ratio.
Insulated signal regenerator;Signal repeater;IP 20 classification;1 insulated channel;Transparent for all PROFIBUS DP protocol versions;RS-485 specifications;Maximum 12 Mbps communication rate;
Converts electrical characteristics of communication signal from the EIA-232 to the EIA-485 specification;No control signal is necessary;Converter circuit provides signal isolation for safe connection between two systems.
SURGE AND TRANSIENT PROTECTOR FOR FIELD DEVICES;For HART/4-20mA, PROFIBUS-PA and Foundation Fieldbus digital networks;Easy installation, connected to every network segment or node,Threaded connection available;Maximum working voltage: 62V.
PROFIBUS-DP TRANSIENT SUPPRESSOR AND ANTI-SURGE;Advanced technology for protection in three stages; Works at 9.6 kbits/s to 12 Mbits/s;• Increases the Profibus network operational safety;• Increases Profibus network availability;• Can be used with Modbus 485.
Digital HART based communication;Updating time of output current in 100ms;Improved performance due to dedicated math co-processor;FMEDA (Failure Modes, Effects and Diagnostic) Analysis;MTBF (Mean Time Between Failures) of 239 years;
Pressure transmitter for gauge and level measurement;Updating time of output current in 100 ms;With high performance mathematical co-processor;Digital electronics and sensor;Weather proof, explosion proof and intrinsically safe;