LS6000 Basic Level Sensor

Economical, basic feature point level switch that can sense a wide range of liquid and dry materials.

More details

New product
 
More info

The LS6000 is a basic, general-purpose level switch that can measure virtually any liquid, dry material or interface of electrically conductive or non-conductive products. The proprietary radio frequency (RF) balanced impedance bridge has exceptional temperature stability, thus eliminating the need to recalibrate the unit from season to season.

When the probe is installed, it is calibrated in absence of material touching the probe. When the desired material comes in contact with the probe, the LS6000 is activated and gives the desired output.

All the necessary calibration indicators are on-board so all you need to calibrate the LS6000 is a small screwdriver.

If the probe you ordered is too long, simply cut it off to the desired length with a saw. If you need to add length, just weld on additional rods. Probes of all lengths are available from the factory.

Fail-safe electronics provide peace of mind. The modular electronics make trouble shooting and repair a snap. The entire unit is backed by our two year warranty.

The probe is made of solid 316 stainless steel rod, the insulator is made of Delrin (teflon and other materials optional). The seals are made with Viton "O" rings. All the electronics are housed in a cast aluminum explosion-proof enclosure.

The solid stainless steel rod is available in a variety of lengths and is suited for liquids or bulk solids. These probes can be coated with Halar in lengths up to 72 inches.

All the necessary calibration indicators are on-board so all you need to calibrate the LS6000 is a small screwdriver. Fail-safe electronics provide peace of mind. The modular electronics make trouble shooting and repair a snap. The entire unit is backed by our two year warranty, 60 day money back guarantee. Special materials of construction are available. Please consult factory.

Features

  • Ignores significant product build up
  • Solid state, no moving parts
  • Simple installation and calibration
  • Explosion proof housing standard
  • Probe length easily field modified
  • Rugged construction handles roughest products

Applications

  • High or low level alarms
  • Sump control
  • Oil/water interface detection
  • Dry pump protection

Liquids:

  • Waste/Wastewater
  • Acids/Caustics
  • Chemicals/Oils
  • Slurries
 

Dry Solids:

  • Flour/Grains
  • Powders
  • Plastics
  • Sand/Cement
  • Wood Chips

Specifications

ELECTRICAL:

Power: 115VAC (+/- 15%) 50/60Hz, 2 watts STANDARD (12 VDC, 24VDC or 230VAC Optional)

Output: 2 Form C Contact DPDT relay, 5 amp resistive at 125, 230VAC; 30VDC

On Board Fuse: 250mA

Failsafe: Selectable High or Low level

RF Frequency: Approx. 1.3 MHz

ENVIRONMENTAL:

Temperature: Delrin insulator -30F to 250F STANDARD
                        Teflon insulator   -30F to 450F (Optional)

Pressure: 1500 psi @ 75F – 1” NPT STANDARD
                  300 psi @ 75F – ¾” NPT (Optional)

Hazardous Area: Housing is CSA and UL approved for Class I, Div. 1, Groups C & D; Class II, Groups E, F & G

Industrial Technical Services from Mississauga, Ontario is a single source Instrumentation and Automation company. We provide certified calibrations, PLC programming, custom controls and Panels.

 
Specifications
Power:120VAC (+/- 15%) 50/60Hz, 2 watts, standard. 230VAC, 12VDC and 24VDC are optional..
Output:2 Form C contacts, DPDT relay, 5Amp resistive at 125VAC, 230VAC; 30VDC.
Fail Safe:Selectable high or low level.
RF Frequency:Approximately 1.3 MHz.
Vessel Entry:1" NPT
Conduit Entry:1" NPT
Hazardous Area:Class I, Group C, D. Class II, Group E,F,G. Class III.
Temperature:Probe: -30 deg F to +250 deg F
Electronics: -40 deg F to 185 deg F
Note: High temperature ratings are available, contact the factory with your application data.
Pressure:1500 psi @ 75 deg F.
Note:High pressure ratings are available, contact the factory with your application data.
Construction:Probe: All wetted parts 316SS, Delrin and Viton.
Electronics: Housed in cast aluminum explosion-proof enclosure.

Contact Us

“Industrial Technical Services is a single source Instrumentation and Automation company. We provide certified calibrations, PLC programming, custom controls and Panels”.

 

Please fill details below and one of our representative will contact you shortly. 

30 other products in the same category: