Pyropress
Argus Range - PPS Engineering polymer or 316 Stainless steel IP67 housing. Flying lead, M20, DIN plug or M12 electrical connection.
Pyropress
Guardian Range - Stainless steel or black anodised aluminium IP66/67 case. Option of dual set point or adjustable deadband.
Pyropress
Perseus Range - Robust black anodised aluminium housing to IP67
Pyropress
Argus Range - ATEX & IECEx Exia IIC Gas Certification. Stainless steel housing. Flying lead connection.
Pyropress
Perseus Range - ATEX/IECEx Exd IIC gas and dust certification. 316 Stainless steel or black anodised aluminium housing
Pyropress
Titan range – ATEX/IECEx Exd IIB + H2 Gas certification. Stainless steel or black anodised aluminium housing
Pyropress
Guardian Range - Stainless steel or black anodised aluminium IP66/67 case. Option of dual set point or adjustable deadband.
Pyropress
Titan Range - Robust Stainless steel or black anodised aluminium housing.
IP66 Environmental protection.
Nuclear approval specification.
Custom
Control
Panels
Certified Calibrations
LS7000/2 Dual-Point Level Sensor
Brand:
Field selectable Auto Fill or Auto Empty;
Solid state, no moving parts;
Simple installation and calibration;
Explosion proof housing standard;
On-board fuse protection.
Love0
The LS7000/2 dual-point RF level switch uses the proprietary radio frequency (RF) balanced impedance bridge. It is specifically designed to automatically fill or empty a tank, vessel or sump. The high and low set points are adjustable over the entire length of the probe. This unit is designed for use in homogeneous liquids.
The dual-point level switch uses a single relay and an on-board latching circuit for automatic operation. No external latching relays or holding contacts are required Simply wire the relay output in series with a pump starter or solenoid valve.
To automatically fill a vessel, select "AUTO-FILL" on the electronics, and the relay will energize when the material is below the "LOW" set point. The pump will turn on and continue to run until the level reaches the "HIGH" set point, then shut off. For "AUTO-EMPTY", the relay action is reversed.
Designed for use in homogeneous liquids only. Coated probe is required for fluids with dielectric constant greater than 12.
The probe is made of a HALAR coated 316 Stainless Steel Rod, 1" NPT process connection and the insulator is made of Teflon. The standard coating is HALAR, but other options such as a Teflon Sleeve are available. The seals are made with Viton "O" rings. All the electronics are housed in a cast aluminum explosion-proof enclosure.
Features
- Field selectable Auto Fill or Auto Empty
- Solid state, no moving parts
- Simple installation and calibration
- Explosion proof housing standard
- On-board fuse protection
- User Programmable time delay
- Modular electronics easily replaced
Applications
- Auto Fill/Auto Empty
- Pump control
Liquids:
- Water
- Acids/Caustics
- Fuels/Oils
- Solvents
Specifications
ELECTRICAL:
Power: 115VAC (+/- 15%) 50/60Hz, 2 watts STANDARD (12 VDC, 24VDC or 230VAC Optional)
Output: 2 Form C Contact DPDT relay, 5 amp resistive at 125, 230VAC; 30VDC
On Board Fuse: .5 A
RF Frequency: Approx. 1.3 MHz
ENVIRONMENTAL:
Temperature: Probe: -30F to 340F - HALAR
-30F to 250F – TEFLON SLEEVE
Pressure: 1500 psi @ 75F – 1” NPT STANDARD
300 psi @ 75 F – ¾” NPT (Optional)
Hazardous Area: Housing is CSA and UL approved for Class I, Div. 1, Groups C & D; Class II, Groups E, F & G
Industrial Technical Services from Mississauga, Ontario is a single source Instrumentation and Automation company. We provide certified calibrations, PLC programming, custom controls and Panels.
16 other products in the same category:
Aqua Metrix
Multi-Parameter Transmitter.
pH, ORP, Conductivity & Flow parameters available.
24 VDC / 24 VDC Loop.
Easy to read 2 X 16 character LCD display.
Quick and easy to calibrate.
Single 4-20mA output
Babbitt International
Side mounted 2 Wire Loop power transmitters provide a 4/20mA output signal that can be sent to a digital display, PLC or DCS. These transmitters are available in several different models.
Anderson Negele
Electronic sensors eliminate hard-to-install capillaries and solves temperature and position compensation issues:
Dual transmitter output eliminates one transmitter and its associated process penetration....
Babbitt International
RADAR Level Transmitters non-contact level measurement of fluids in a metal tank
Anderson Negele
For monitoring liquid inventory levels in virtually any atmospheric storage application.
Top-mount configuration provides for easy installation without special fixturing or welding.
Micro-processor based platform....
Anderson Negele
Monitor liquid inventory levels in almost all atmospheric storage application
Top-mount configuration
Micro-processor based platform
Quick Disconnect Receptacles with optional Field Wiring Connectors
Standard...
Babbitt International
Accurate, safe and reliable continuous level indication and control in hazardous and non-hazardous applications.
Babbitt International
Continuous measurement of electrically conductive liquids that do not leave a sticky residue or buildup.
GFG Instrumentation
RC2 Remote Control can be used for control or adjustment of the zeropoint and sensitivity when testing the transmitter
Babbitt International
Non-invasive alarm switches which clamp to the side of the chamber and are magnetically actuated by the float through the chamber wall.
Aqua Metrix
Non-contact ultrasonic level measurement.
Narrow 8 degree beam angle.
Outputs 0-20 mA and RS-485.
Plug-and-play setup. No calibration.
Intuitive software included.
Software control of analog range, span and...
Babbitt International
Ignores significant product build up;Solid state, no moving parts;Simple installation and calibration;Explosion proof housing standard.
Anderson Negele
Measures liquid level in sanitary applications.
Fewer tune-ups.
No more overflows.
More reliable inventories.
3-A compliant.
Quick Disconnect
Receptacles with optional Field Wiring Connectors.